Description of available pieces
Straight Pipe - Features fully unitized, twist-lock construction
in 3” and 4” diameters. Listed at 1” clearance
to combustibles in the USA. It can be used in both vertical and
horizontal installations. Stainless steel welded seam inner wall,
combined with a galvalume welded seam outer wall. Pipe OD is diameter
plus 5/8”. To calculate installed length, subtract 1 1/2”
from each length of pipe.
Flex Pipe - Use for offsetting rigid pipe around
smoke shelf in masonry chimney only. Allows for offsets with biofuel
appliances. Female and male ends twist-lock. Female end swivels
for easy alignment.
Not for use in attic or wall spaces.
45 degree Elbow - Offsets obstructions as needed.
Elbows swivel 360° at base. Angle not adjustable.
90 degree Elbow - Offsets obstructions as needed.
Elbows swivel 360° at base. Angle not adjustable.
Adapter Tee with Clean-Out Tee Cap - Use for a
90° offset. Attaches directly to appliance as an adapter. Removeable
twist-lock Clean-Out Tee Cap.
Adjustable Roof Flashing - Use to weather proof
the penetration of vent pipe through the roof. Storm Collar required.
Select roof flashing based on pitch of roof.
Adjustable Wall Strap - Use to support vent pipe
or tee sections. Adjusts to provide 1”- 3” clearance.
Appliance Adapter - Use to attach to appliance
outlet allowing for easy pipe connection. Seal adapter to appliance
with high temperature sealant.
Attic Insulation Shield - Required for installations
that pass through an attic to prevent insulation and debris from
accumulating near the vent. Provides 1” clearance to combustibles.
Chimney Adapter -Use to transition between PelletVent
Pro to existing chimney such as DuraTech, DuraPlus or DuraPlus HTC.
Requires a DVL/ DuraBlack Chimney Adapter to fasten into support
box or wall thimble.
Clean-Out Tee Cap - Use as a replacement Clean-Out
Tee Cap.
DSA Roof Flashing - Use with metal or tile roofs.
Available in 0/12-6/12 and 7/12-12/12 styles. Made of dead soft
aluminum.
Horizontal Cap - Use for horizontal terminations
only. The Horizontal Cap can be turned at the gore to direct exhaust
output. Designed to create a venturi effect to force exhaust out.
Made of a laser-welded, super-ferritic stainless steel inner wall
that is scientifically proven to resist corrosion from corn and
other biofuels. Outer wall made of laser-welded stainless steel.
House Shield - Use to protect exterior of structure
from blower discharge in horizontal venting applications.
Increaser Tee with Clean-Out Tee Cap - Attaches
3” pipe to branch and 4” pipe to body. Use for a 90°
offset. Branch swivels for alignment. Removeable twist-lock Clean-Out
Tee Cap.
Single Tee with Clean-Out Tee Cap - Use for a 90°
offset. Branch swivels for alignment. Removeable twist-lock Clean-Out
Tee Cap.
Snow Splitter - Use to divert snow around chimney,
vent, and roof flashing. Constructed of paintable galvanized material.
Ships flat for easy assembly.
Square Horizontal Cap - Use for horizontal terminations
only. Cap features swivel collar to adjust exhaust direction. Cap
features an optional swivel base.
Storm Collar - Use to maintain a weather tight
resistant seal between the pipe and the flashing.
Tall Cone Roof Flashing - Use to weather proof
the penetration of vent pipe through the roof. Storm Collar required.
Select roof flashing based on pitch of roof. Use on flat roofs,
chase enclosures, or masonry chimney. Made of galvalume.
Vertical Cap - Use for vertical installations only.
Required where pipe terminates above the roof line.
Wall Thimble - Use for through-the-wall installations.
Fits between standard wall studs. Comes with an insulation ring
to reduce air infiltration where the pipe slips through the thimble.
